Omega PASS-3 Ford PATS1 Anti-Theft System Bypass (DB-PASS-3) NEW

Description

FREE Standard Shipping
Omega PASS-3 Ford PATS1 Anti-Theft System Bypass
(DB-PASS-3)
Please message through eBay any questions you may have before making a purchase.
Our experts recommend, make sure it work with your vehicle.
Compatible with select model vehicle.
Priced and Sold as: EACH
Professional Installation May Be Required
Ford PATS1 Anti-Theft System Bypass
This module allows the remote car starter to be installed and correctly operate 1996-99 vehicles equipped with the Ford PATS or Securi Lock Theft Deterrent System
Bypass is activated only when the remote start module engages. Includes the needed transponder. This module is plug-n-play compatible with all Omega remote start systems.
PASS3 Bypass Module for Remote Starting
Programming the PASS3 Transponder The PASS3 transponder must be programmed to be recognized by the vehicle's PATS system.
If your application is not listed below, the programming procedure is usually found in the vehicle's owner's guide.
1998 Continental, Crown Victoria, Explorer, Grand Marquis, Mountaineer and Town Car
1) Complete the installation of the PASS3 transponder.
2) Two programmed keys are required. Turn the ignition switch on (leave on at least 1 second), then off with the first programmed key. Remove the first key from the ignition switch.
3) Within 5 seconds, insert the second key and turn the ignition switch on, then off. Remove the second key from the ignition switch.
4) Within 10 seconds, activate the remote starter unit.
5) If the PASS3 transponder was successfully programmed, the engine remains running. If the THEFT light flashes and the engine stalls, reposition the PASS3 transponder. All keys programmed previously will still operate. 1998-99 Contour and Mystique
1) Complete the installation of the PASS3 transponder.
2) Turn the ignition switch on and off 3 times with a programmed key. Remove the key from the ignition switch.
3) Within 5 seconds, activate the remote starter unit.
4) If the PASS3 transponder was successfully programmed, the THEFT light will be on for 2 seconds and the engine remains running. If the THEFT light flashes and the engine stalls, reposition the PASS3 transponder. All keys programmed previously will still operate.
1998-99 Full Size Pickup, Expedition and Navigator
1) Complete the installation of the PASS3 transponder.
2) Turn the ignition switch on and off with a programmed key. Remove the key from the ignition switch.
3) Within 15 seconds, activate the remote starter unit.
4) If the PASS3 transponder was successfully programmed,
The THEFT light will be on for 2 seconds
and the engine remains running. If the THEFT light flashes and the engine stalls, reposition the PASS3 transponder. All keys programmed previously will still operate. 1998-99 Mark VIII
1) Complete the installation of the PASS3 transponder.
2) Turn the ignition switch on with a programmed key. After the Anti-Theft light stays on 3 seconds, remove the key from the ignition switch.
3) Within 15 seconds, activate the remote starter unit.
4) If the PASS3 transponder was successfully programmed, the Anti-
Theft light will be on for 3 seconds and the engine remains running.
If the Anti-Theft light flashes and the engine stalls, reposition the PASS3 transponder.
All keys programmed previously will still operate. 1996-99 Mustang, Taurus and Sable
1) Complete the installation of the PASS3 transponder.
2) Turn the ignition switch on, then off with a programmed key. Remove the key from the ignition switch.
3) Within 15 seconds, activate the remote starter unit.
4) If the PASS3 transponder was successfully programmed, the THEFT light will be on for 2 seconds and the engine remains running. If the THEFT light flashes and the engine stalls, reposition the PASS3 transponder. All keys programmed previously will still operate. 1998-99 Mustang, Sable and Taurus
1) Complete the installation of the PASS3 transponder.
2) Two programmed keys are required. Turn the ignition switch on (leave on at least 1 second), then off with the first programmed key. Remove the first key from the ignition switch.
3) Within 5 seconds, insert the second key and turn the ignition switch on, then off. Remove the second key from the ignition switch.
4) Within 10 seconds, activate the remote starter unit.
5) If the PASS3 transponder was successfully programmed, the engine remains running. If the THEFT light flashes and the engine
stalls, reposition the PASS3 transponder. All keys programmed previously will still operate. Permanently adhere the transponder in place with epoxy resin or silicone sealant. Then, thoroughly test the remote starting unit's operation before reassembling the steering column and dash parts. PASS3 Bypass Module for Remote Starting The Passive Anti-Theft System (PATS) utilizes Passive Transponder technology. Specialized ignition keys are used with vehicles equipped with this system. These keys contain a Passive Transponder, which is a miniature radio transmitter.
The system within the vehicle will not allow the engine to remain running unless it receives a digitally-encoded radio signal from Passive Transponder within the key. Adding a remote starting unit to vehicle equipped with PATS also requires adding the PASS3 bypass module. The PASS3 only bypasses the PATS system during remote starting; the PATS system remains operational and effective at all other times. The Passive Transponder is a miniature radio receiver and transmitter that requires no batteries. When the ignition switch is turned on, the PATS system transmits Radio Frequency (RF) energy. This energy is received by the Passive Transponder in the key, stored, then used as the operating power for its own signal transmission back to the PATS system. The signal transmitted by the Passive Transponder contains a digitally-encoded message which the PATS system has previously been programmed to recognize. When the PATS control unit receives the correct signal, the vehicle can be started and the engine remains running.
All of these operations take only milliseconds.
Operation of the PATS system requires no conscious action on the part of the user - when the key with the Passive Transponder is inserted into the switch, the transponder is within range of the antenna. The radio transmissions are then made when the ignition switch is turned on and the engine is allowed to start and remain running.
The PATS system has a special antenna, which is part of the Transceiver Module, mounted behind the steering column trim panel.
The PATS system has a special antenna, which is part of the Transceiver Module, mounted behind the steering column trim panel. This antenna appears as a Black collar around the ignition switch. Follow these steps:
1) Remove the steering column trim panels. Locate the Black PATS antenna collar.
2) Route the Red 3-pin connector to Omega remote starter module; all other remote starter connections should be made first.
3) Position the PASS3 transponder as shown in the diagram; it can be held in place temporarily with tacky tape.
4) Follow the programming instructions on the reverse side.
5) Upon successful programming of the PASS3 transponder, permanently adhere the transponder with epoxy or silicone.
6) Thoroughly test the remote starting unit's operation before reassembling the steering column and dash parts.
Shipping Information:
TERMS & CONDITIONS
We offer FREE ground shipping, USPS estimated delivery time 3-12 days in the
within the USA.
USPS, delivery times and date are not guaranteed.
Most orders are processed and Ships Monday through Friday (excluding public holidays)
Customer responsible for paying VAT, Duties, Import tax and Customs fees
Note: Most items ship in a plain brown box/packaging.
As soon as you purchase and pay for the item, the order will ship as quickly as possible.
Our team will ship your order to the verified shipping address provided by eBay / PayPal ONLY.
Prices, Product availability, and specifications are subject to change without notice.
Order that have
has already shipped, you won't be able to cancel it
Please provide your full name and address (No P.O. Box) for shipping and handling purposes.
We utilize USPS or UPS for shipping, orders may require a signature confirmation for tracking to deliver packages.
All packages Refused or undeliverable due to insufficient address, or marked as Unclaimed, is subject to a 15% restocking fee.
All returns orders will be charge shipping costs from both sides, will be subtracted from your purchase price
Note: USPS and UPS do not offer their services for free and shipping charges are non-refundable.
Buyers pay return shipping and insure your pack.
DISCLAIMER: All product brands names, logos, and or registered® trademarks are property of their respective owners. All product on this website are for identification purposes only. Use of these names, logos, and brands does not imply endorsement.